6. Control center

  • Control center
    1. Users can enter the engraving control interface by clicking on the engraving control box on the homepage to control and operate the engraving machine.
    2. The top shows the current status of the engraving machine, engraving speed, laser power and laser location.
    3. Equipment remote control, including direction control, zeroing, reset and other button functions
    • Status display box (Status display (A-1): Indicates the current machine status. The machine has the following status)
      1. IDLE: normal signal communication;
      2. JOG: running "single point motion";
      3. RUN: Running "automatic motion";
      4. CHECK: Check equipment;
      5. HOME: Running "Home to Zero";
      6. DOOR: safety door;
      7. UNKNOW: The signal status is unclear;
      8. ALARM: Alarm status (unlocking "$X" can relieve this status);
      9. SLEEP: sleep state;
      10. HOLD: pause state.
    • F, S:

      • F: Instantaneous speed of the engraving machine, unit: mm/min;

      • S: Laser power is a parameter in the G code. The maximum value of the equipment is generally 1000, that is, (S/Smax*100%) is the power percentage of the laser head at this moment.

    • X, Y, Z: Indicates the XYZ axis coordinate position of the current engraving machine
    • Remote control parameter selection
      • The upper column: 0.1mm, 1mm, 10mm, 50mm represents the distance moved by the remote control bar of the device with a single click;
      • Lower column: slow speed (2500mm/min), medium speed (5000mm/min), fast speed (7500mm/min), extremely fast speed (10000mm/min), indicating the current moving speed
    • Device remote control bar
      • B-1: Reset, perform a soft reset on the device, and the reset will enter the ALARM state in the running state;
      • B-2: After clicking the button, the device will move along the positive direction of the X-axis at the distance and speed selected by the remote control parameters;
      • B-3: Stop jogging: The device is in JOG mode, clicking will stop the movement at this moment;
      • B-4: After clicking the button, the device will move along the positive direction of the X-axis at the distance and speed selected by the remote control parameters;
      • B-5: After clicking the button, the X, Y, and Z axes will be reset. The X, Y, and Z axes will be moved to the mechanical origin and reset the coordinates to 0;
      • B-6: After clicking the button, the device will move along the negative direction of the X-axis at the distance and speed selected by the remote control parameters;
      • B-7: Unlock: The device is in the "ALARM" state, and will be converted to IDLE for normal operation after clicking;
      • B-8: After clicking the button, the device will move along the negative direction of the X-axis at the distance and speed selected by the remote control parameters.
    • Device function control
      • 1. Set the starting point: set the relative coordinate to 0 point, and set the mechanical coordinate at this time to 0 point.
      • 2. Return to the starting point: The device will move to the set relative origin.
      • 3. Laser: turn on or off the laser; pay attention to the safety of the use of the laser, prevent it from irradiating the glasses before turning it on, and be careful after turning it on.
        Always pay attention to fire prevention. After turning on the laser, you can drag the upper slide bar to adjust the laser power.
      • 4. Range: Positioning engraving range function; (Note: After setting a new zero point, the point range may exceed the soft limit. This
        You need to reset to unlock the device; when entering the preview page, the image engraving range will be positioned. )
      • 5. Fan: Turn on or off the fan.
      • 6. Light: Turn on or off the light.
      • 7. Tilt check: Turn on or off tilt check; after turning it on, an alarm will sound if the device tilts. NOTE: For your safety, it is not recommended that you turn off flame detection.
      • 8. Offset detection: Turn on or off offset detection; after turning on, the device will stop running if it offsets.